MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > Heat Treating and Metallurgy

Heat Treating and Metallurgy Discussion of heat treatment and metallurgy in knife making.

Reply
 
Thread Tools Display Modes
  #1  
Old 07-28-2006, 09:48 PM
Karl B. Andersen's Avatar
Karl B. Andersen Karl B. Andersen is offline
Skilled
 
Join Date: Apr 2005
Location: Warba, Minnesota
Posts: 613
heat treating W1

Can anyone refer me to a decent W1 heat treating formula?
Or, does anyone have one they prefer and would care to share?
Something reliable, I hope!
Thanks!


__________________
Blade Show Table 8-Q

What do you do when you see your ex in pain, limping and bleeding?

Relax. Take a deep breath. Reload and then shoot again.

http://www.andersenforge.com/
Reply With Quote
  #2  
Old 07-30-2006, 11:37 AM
John Frankl John Frankl is offline
Steel Addict
 
Join Date: Jun 2002
Location: Boston, MA
Posts: 205
I would search this forum, bladeforums, and Don Fogg's forum for posts on W1 by Randall Graham and Nick Wheeler. They have both written alot of really great stuff.

JOhn


__________________
John Frankl
Reply With Quote
  #3  
Old 07-31-2006, 07:44 PM
Don Hanson's Avatar
Don Hanson Don Hanson is offline
Steel Addict
 
Join Date: May 2006
Location: By the river in Missouri
Posts: 188
Karl, W1 is one of my favorite steels. It is basicly a better grade of 1095. I heat to 1450 hold for a few min.s then quench in a fast oil, then two one hour tempers at 400 deg.s. I am forging blades from W1 drill rod and it's been a very, very clean steel with predictable results.

I forgot to mention that I finish forging with lower heats and also normalize once just above critical then agian at critical and last at just below critical. I also like to soak for one hour at 1300 deg.s in my kiln. After reading alot of Kevin Cashen's posts, I am rethinking the way I heat treat a have started working with the info he has be sharing. Thanks Kevin


__________________
N-T 'Hammerin Crappie Hanson'
Don Hanson
www.sunfishforge.com

Last edited by Don Hanson; 07-31-2006 at 10:12 PM.
Reply With Quote
  #4  
Old 07-31-2006, 09:55 PM
Drunkenduck Drunkenduck is offline
Steel Addict
 
Join Date: Feb 2006
Location: Portsmouth, VA
Posts: 139
Send a message via ICQ to Drunkenduck
Wink quick question

Don, just a quick question. It may be a little off topic, but what team does you cat play for?

Doug Lester
Reply With Quote
  #5  
Old 08-01-2006, 04:19 PM
shgeo shgeo is offline
Steel Addict
 
Join Date: Feb 2003
Location: NW New Mexico
Posts: 133
Quote:
Originally Posted by Drunkenduck
Don, just a quick question. It may be a little off topic, but what team does you cat play for?

Doug Lester
The Detroit Limes, of course.


__________________
"I want to play with your poodle"
Lightnin' Hopkins, long ago


Steve Hayden steve4663@gmail.com
Aztec, NM
Reply With Quote
  #6  
Old 08-01-2006, 06:20 PM
Don Hanson's Avatar
Don Hanson Don Hanson is offline
Steel Addict
 
Join Date: May 2006
Location: By the river in Missouri
Posts: 188
Quote:
Originally Posted by shgeo
The Detroit Limes, of course.
Yep and a bad cat it is, see that look on it's face?


__________________
N-T 'Hammerin Crappie Hanson'
Don Hanson
www.sunfishforge.com

Last edited by Don Hanson; 08-01-2006 at 06:39 PM.
Reply With Quote
  #7  
Old 08-03-2006, 03:44 AM
Karl B. Andersen's Avatar
Karl B. Andersen Karl B. Andersen is offline
Skilled
 
Join Date: Apr 2005
Location: Warba, Minnesota
Posts: 613
Thanks, Don. I'll see how that works for me.


__________________
Blade Show Table 8-Q

What do you do when you see your ex in pain, limping and bleeding?

Relax. Take a deep breath. Reload and then shoot again.

http://www.andersenforge.com/
Reply With Quote
  #8  
Old 08-03-2006, 03:51 AM
Karl B. Andersen's Avatar
Karl B. Andersen Karl B. Andersen is offline
Skilled
 
Join Date: Apr 2005
Location: Warba, Minnesota
Posts: 613
Don, do you bring the blade up to temp WITH the oven, or do you put it in after the oven has reached soak? Is this accomplishing a sperodizing procedure? I do something similar with my 5160, yet a much longer soaking segment, and it does a great job. I got the "recipe" from Tim Zowada, who helps design Even Heat's knife ovens and salt pots. Really makes the steel easy to work with, and brings everything equal making for a good hardening! I swear, after doing my sperodizing anneal, my steel gets harder on quench.


__________________
Blade Show Table 8-Q

What do you do when you see your ex in pain, limping and bleeding?

Relax. Take a deep breath. Reload and then shoot again.

http://www.andersenforge.com/
Reply With Quote
  #9  
Old 08-03-2006, 07:35 AM
Don Hanson's Avatar
Don Hanson Don Hanson is offline
Steel Addict
 
Join Date: May 2006
Location: By the river in Missouri
Posts: 188
Karl, I bring the oven up to 1300 with the blade in, then hold for an hour. I started doing this years ago with my billets of mosaic damascus bolster stock that needed to go to the bandsaw. I like the way the steel cut and drilled so I started doing it with my blades. I didn't know what it was called until reading some of Cashen's writings but I did know it was good. I think Al Dippold told me about this. I also do one normalize before I quench.


__________________
N-T 'Hammerin Crappie Hanson'
Don Hanson
www.sunfishforge.com
Reply With Quote
  #10  
Old 08-17-2023, 07:55 PM
astmsteel astmsteel is offline
 
Join Date: Feb 2016
Posts: 1
Quote:
Originally Posted by Karl B. Andersen View Post
Can anyone refer me to a decent W1 heat treating formula?
Or, does anyone have one they prefer and would care to share?
Something reliable, I hope!
Thanks!
You can refer to these W1 steel properties and heat treatment values in this post.
Reply With Quote
Reply

Tags
blade, ca, forging, heat, heat treating, heat treatment, knife, post


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:46 AM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved