![]() |
![]() |
![]() |
|
![]() |
![]() |
||
![]() |
![]() |
|
![]() |
|
The Sheath/Holster Makers Forum This is the place to discuss all forms of sheath and holster making. |
![]() |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Belt loop stitching my rub blade edge.
Decided to make up a small sheath for a utility type knife. The section that I have stitched the belt loop in place those stitches are very close to where the blade will be inserted. I'm concerned that the repeated draw and insertion may cut them over time.
Thoughts on how to protect the stitching in that area? __________________ Mike ![]() ![]() |
#2
|
|||
|
|||
Do you have some thin leather to line it with?
Or stitch over it? Some guys also put some epoxy over it as well. I have taken to lining the inside with 4 oz veg tan dyed to match the rest of the sheath.
Last edited by jimmontg; 06-27-2018 at 08:46 PM. |
#3
|
||||
|
||||
Excellent! Have some odd cuts of pig and deer skin that is pretty thin that can be glued in.
__________________ Mike ![]() ![]() |
#4
|
|||
|
|||
Michael, make sure the leather you use is NOT chrome tanned as in time it will corrode even stainless.
|
#5
|
|||
|
|||
You also need a groover to bury those stitches below the level of the leather do they can't be touched.
|
#6
|
||||
|
||||
Thanks guys! Not sure of the tanning method for the thinner pieces. Picked those up from an upholstery shop of various cuts. The original intent was to be used as an overlay on the outside of the sheath. I'll rework this so that the stitching is recessed and skive a piece over to that section with a known leather. Haven't had to do this on the usual sized sheaths so a new adventure.
Making knives sure brings plenty of challenges to learn. ![]() __________________ Mike ![]() ![]() |
#7
|
||||
|
||||
Use the groover as Argel55 mentioned and set stitches just below the surface, tap down smooth with flat faced cobblers hammer. Most furniture and garment leathers are chrome/chemical tanned. If they get a little damp will start rust/corrosion on blades and/or guards.
Another technique that is seldom used these days - pre-punch your stitfhing holes then use a very sharp chisel to curl up the leather over the length of the stitch line, pull back the flap and stitch then glue the flap back down over the stitches. Again, tap down flat with hammer - totally hidden stitches. __________________ Carl Rechsteiner, Bladesmith Georgia Custom Knifemakers Guild, Charter Member Knifemakers Guild, voting member Registered Master Artist - GA Council for the Arts C Rex Custom Knives Blade Show Table 6-H |
![]() |
Tags |
art, belt, belt loop, blade, ca, edge, guards, hidden, holster, how to, knife, knives, leather, leather die, leather tooling, make, sheath, sheaths, shop, small, stainless, stitch, tanning, thin, utility |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tight Belt Loop | AlanR | The Sheath/Holster Makers Forum | 3 | 08-12-2009 11:35 PM |
Getting belt loop smoother ? | Rodney Rasberry | The Sheath/Holster Makers Forum | 6 | 07-23-2007 01:05 PM |
belt loop location help. | Brett Holmes | The Sheath/Holster Makers Forum | 5 | 07-16-2006 07:17 PM |
How Do You Center A Belt Loop? | cavetech | The Sheath/Holster Makers Forum | 10 | 04-12-2006 09:09 PM |
Belt loop ? | Alain M-D | The Sheath/Holster Makers Forum | 9 | 10-02-2003 06:21 PM |