MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Tool Time

Tool Time Let's talk shop. Equipment, Tips & Tricks, Safety issues - Post it here.

Reply
 
Thread Tools Display Modes
  #1  
Old 06-04-2012, 08:45 PM
NGsportsman NGsportsman is offline
Member
 
Join Date: Apr 2012
Posts: 10
Tell me about my anvil

I just bought my first anvil, and I know next to nothing about anvils.

It was in an old shop, underneath an old workbench, covered in cobwebs, sawdust and old grease. It weighed 126# on a set of bathroom scales and it gave good rebound when struck with a hammer. I gave $200 for it.

After cleaning it up, I can find no distinguishing marks, other than the number 13 raised above the base under the horn.

Can anyone tell by looking at the picture, what did I stumble on? Are there other ways to possibly identify manufacturer?

Reply With Quote
  #2  
Old 06-17-2012, 02:22 AM
EdStreet EdStreet is offline
Guru
 
Join Date: Sep 2005
Location: Columbus, GA
Posts: 1,050
Honestly there are so many out there that are improperly marked that it is almost impossible to tell who made it. I have one like this and I cleaned it up good, did see a few numbers but that's it. Some of the peter wright anvils has this shape but the most important factor is the bounce test. If that is good then it's a good anvil.

As for being half real half cast I am going to leave that up to others to debate.

This looks almost identical to mine excpt mine is 250 pounds.


__________________
Gold is for the mistress - silver for the maid
Copper for the craftsman cunning in his trade.
"Good!" said the Baron, sitting in his hall
But steel - cold steel is master of them all.
Rudyard Kipling (1865 - 1936)
Reply With Quote
  #3  
Old 06-17-2012, 11:34 AM
Ed Tipton Ed Tipton is offline
Skilled
 
Join Date: Apr 2009
Posts: 352
NGsportsman...There is not a lot to go on here, but your anvil resembles those made by the II&B company who also made the Vulcan anvils. The shortness of the horn and also the deep "drop" of the horn into the base is the closest thing to an indicator that I can see. The only thing is that I have never seen either a Vulcan or an II&B anvil that was not clearly marked as such....but there is always a first....
Reply With Quote
  #4  
Old 01-09-2013, 05:12 PM
teddharris teddharris is offline
 
Join Date: Dec 2007
Posts: 2
Could you show a pic of the mark under the horn? Might be something that will help identify the anvil. 126# is a good minimum weight for blade forging. Have fun with your new anvil1
Reply With Quote
  #5  
Old 07-14-2015, 07:03 AM
Moby Duck Moby Duck is offline
 
Join Date: Aug 2013
Location: New Zealand
Posts: 1
Anvil weight

A few years late with this answer but the 113 marking defines this anvils weight.
The first figure is for 1 hundredweight (that is 112 pounds) + 13 pounds for a total weight of weight of 125lbs which is very close to what your scales measured 126 lbs. Possibly made in the U.K. with this sort of marking. Unlikely to be a famous maker if they weren't proud enough to cast their mark into it. Does the makers name really matter ? It looks like a very nice anvil and if it rings true that is all that really matters.
Reply With Quote
  #6  
Old 09-01-2015, 05:09 PM
Bwitty Bwitty is offline
Enthusiast
 
Join Date: Jan 2004
Location: Plano, Tx
Posts: 88
That looks alot like an Arm& Hammer Anvil. Cast body with a Steel face. I used to have a 100lb one


__________________
Byron WItty
Member TKCA

"A good friend is someone you can call to bail you out of jail. A TRUE friend would be sitting next to you saying how did we get into this
s#$%!!"
Reply With Quote
  #7  
Old 09-01-2015, 06:15 PM
BCROB's Avatar
BCROB BCROB is offline
Master
 
Join Date: Dec 2011
Location: BC
Posts: 884
Looks Vulcan , will do you just fine , the face and horn look in really good shape....welcome to the addiction !


__________________
R.Watson
B.C. Canada
Reply With Quote
  #8  
Old 09-02-2015, 04:05 PM
Bwitty Bwitty is offline
Enthusiast
 
Join Date: Jan 2004
Location: Plano, Tx
Posts: 88
My bad Vulcan would be the correct name. They used the Arm&Hammer logo


__________________
Byron WItty
Member TKCA

"A good friend is someone you can call to bail you out of jail. A TRUE friend would be sitting next to you saying how did we get into this
s#$%!!"
Reply With Quote
  #9  
Old 01-30-2016, 10:48 AM
ltcray ltcray is offline
 
Join Date: Oct 2005
Location: America
Posts: 4
You got a good deal on that. Anvilfire.com has a good page explaining what to look for in an anvil, including what you should expect to spend. They said a Chinese sand cast door stopper (very low grade anvil) could go for $1/lb. Lower midgrade like my Star 100# runs about $2-3/lb.
If you got a ring out of yours I would have to say you're at least in the higher midgrade, moving into the top grade. Mine doesn't ring at all.... it just goes ~ whap!~.
Reply With Quote
Reply

Tags
anvil, blade, forging, hammer, horn, knife, made, makers, sand, scales, steel


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Old, Old Anvil nifeman The Outpost 7 03-19-2009 04:18 PM
New Anvil nc_cooter The Outpost 6 06-01-2008 07:52 PM
Anvil? I'm looking Tarl_cabot Tool Time 4 06-28-2005 08:59 PM
New Anvil Woo Hoo!!! jdlange The Outpost 9 01-21-2003 03:57 PM
New Anvil Sweany The Outpost 19 01-18-2002 10:35 AM


All times are GMT -5. The time now is 06:16 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved