|
|
Register | All Photos | FAQ | Members List | Calendar | ShopStream (Radio/TV) | Search | Today's Posts | Mark Forums Read |
The Newbies Arena Are you new to knife making? Here is all the help you will need. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Wood, scales, and other items of interest?
O.K., not sure if this is the proper place for this...if not, please move it.
!. I find my self needing thicker wood for my knife scales, and an occasional set of revolver grips, and I like highly-figured wood It it is almost impossible to find scales thicker than 3/8in. and 2-21/2 in. wide for a reasonable price on da Bay. Can anyone suggest a source ? 2. I've seen YouTube demonstrations on stabilization, using some pretty primitive equipment...a Ball canning jar, and an automotive (I presume) brake vacuum pump. I won't use enough stabilized wood to make an investment in one of the expensive set-ups cost-effective. So, has anyone tried the YouTube way, and how did it work? 3. What is Cactus Juice? 4. Drilling the hole the long way through the handle for a hidden-tang knife: I don't think I want to free-hand it. I figure if I mark the centers of both ends of the handle block, then square everything up in my drill press vise, and raise the table when I get to the end of the press' 2 inch throw, I should eventually get the holes to meet somewhere in the middle without too much off-center. Am I an optimist? Is there a better way? I'm going to practice on a block of Basswood before I even think of trying to drill a good block of handle material. Thanks. |
#2
|
||||
|
||||
Quote:
Using the drill from both ends method, you should be able to get very close. If I'm going to use stabilized wood, I want it to be stabilized right, so no back-yard method is adequate IMO. KMG does it well. __________________ A good friend told me one time about forging "What is there not to like, you get to break all the rules you were told as a kid, don't play with that it is sharp, don't play with fire, and don't beat on that" Wade Holloway See some of my work. |
#3
|
|||
|
|||
"If I'm going to use stabilized wood, I want it to be stabilized right, so no back-yard method is adequate IMO. KMG does it well."
I'm glad to hear others say this, we recently had a very heated discussion about "home brew" methods on the facebook group. Several knifemakers from here (including myself) were on the side of sending it to a pro. I admitted to doing the home grown method myself, but not for blades I was going to sell. |
#4
|
|||
|
|||
Buy your wood in blocks and cut your scales to fit. You can usually get better deals on fleabay that way. Look for that thread "you wanna trade". There may be someone there that has some.
|
#5
|
||||
|
||||
Quote:
Yeah, buy the blocks and cut them into scales... blocks are usually 1 inch thick or more. __________________ A good friend told me one time about forging "What is there not to like, you get to break all the rules you were told as a kid, don't play with that it is sharp, don't play with fire, and don't beat on that" Wade Holloway See some of my work. |
#6
|
|||
|
|||
I take it that you have a way to re-saw a block of wood. I use a band saw with a 1/2" blade. Go to some of the wood turning sites on line and see if they have any spindle stock in a wood that you are interested in. I usually get something in 1 1/2 X 1 1/2 or 2 X 2. Smaller bowl blanks might also be a possibility.
I use the same method for drilling holes. If you mark the centers on both ends then you have two points which determine a straight line. I clamp a board that has the end of a screw sticking out of it to the stage of my drill and line the chuck up on it with a straight rod and then clamp everything down tight. Cactus Juice is a wood hardening product that some people on these board like for stabilizing wood. I would rather send my wood out to an outfit that has real equipment and the expertise to do the job right. BTW, I've had a few "heated" discussions about wood stabilization and a couple of other things on these sites. The knack is learning when to drop it. Remember, never get into an argument with an idiot. You'll confuse the by-standers and they won't be able to tell who's who. Doug __________________ If you're not making mistakes then you're not trying hard enough |
#7
|
|||
|
|||
You are 100% correct in my opinion Doug.
|
#8
|
||||
|
||||
Quote:
"Never argue with an idiot. They will only bring you down to their level and beat you with experience" Mark Twain :-) |
#9
|
|||
|
|||
Dan, I like that version too.
Doug __________________ If you're not making mistakes then you're not trying hard enough |
#10
|
|||
|
|||
Thanks for the replies, all.
300 Musk Ox Horn??? Not quite my speed, yet! Also. who or what is KMG? I had some stabilization done by someone, whose name I can't recall, and it came back really lumpy and rough. I think I might be able to sand it down to useful flatness, but am not sure. I figured I could do at least as well with DIY stabilization, but maybe not. Is a dust mask required for sanding stabilized woods? Unfortunately, I have no way to resaw lumber. My shop does not have space for even a small band saw, and still leave room enough on the workbenches for woodcarving, reloading, and just general puttering. I'll figure it out. Again, Thanx for the help and suggestions. |
#11
|
|||
|
|||
Wear your dust mask. I don't have a band saw. A jig saw and hand saw is all I use.
|
#12
|
||||
|
||||
KMG is the brand name of the most popular 2x72" grinder used by many knife makers.
Do as the others have suggested and send any wood you want stabilized out to a pro outfit like K&G Finishing in Lakewood, AZ. At this stage of your knife making journey you don't need to waste time and money with side projects that will just eat up your resources. Spend the money on the tools and materials you need instead. Not a dust mask - a respirator. That's a half face mask with two canister cartridges AND dust filters. Pretty much required for any knife maker who doesn't have a spare set of lungs ... |
#13
|
||||
|
||||
My apologies, I ment K&G, not KMG...
__________________ A good friend told me one time about forging "What is there not to like, you get to break all the rules you were told as a kid, don't play with that it is sharp, don't play with fire, and don't beat on that" Wade Holloway See some of my work. |
#14
|
||||
|
||||
You might consider Wood Stabilizing Specialist (WSSI). They were the first ones I started with for stabilized wood and have always been a favorite of mine for both wood supply and having my wood stabilized.
He has also done specialized cuts for me such as when I needed a couple handles for straight razors. There is a delay but I feel it is worth the wait and I've never been disappointed by his selection of wood. Jim __________________ I cook with a flair for the dramatic, and depraved indifference to calories |
Tags |
back, blade, blades, block, demo, easy, handle, handle material, hidden, home, horn, jig, knife, knife scales, knives, make, material, press, primitive, scales, stabilization, tang, throw, vise, wood |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rock and wood scales | reddirt | The Newbies Arena | 3 | 02-15-2009 07:57 AM |
Wood for scales?? | Mitchell H. | The Newbies Arena | 7 | 06-23-2005 10:14 AM |
wood scales, slabs | ragnik | The Supply Center | 14 | 08-24-2003 09:50 PM |
Wood scales | P MOORE | The Supply Center | 4 | 03-14-2002 01:00 PM |