|
|
Register | All Photos | FAQ | Members List | Calendar | ShopStream (Radio/TV) | Search | Today's Posts | Mark Forums Read |
The Newbies Arena Are you new to knife making? Here is all the help you will need. |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Help with anvil identification
I have a chance to pick this up at a Brother in law discount but im not sure the value. I think it's a Fisher but I haven't weighed it but it's heavy.
Any insight would be appreciated. __________________ Mark Last edited by mwhuston; 09-03-2018 at 10:13 PM. |
#2
|
|||
|
|||
It looks to be in good shape. I have never seen an anvil with hold downs forged into the base. It is a wrought anvil because you can see where the steel plate is forge welded on. Is the "20" the only marking? Unusually on old anvils there are 3 numbers on one side like 1 2 3. That is a 100 weight marking but does not designate 100 pounds, it is 112 pounds. So the first number is the hundred weight number. In this example 112 pounds. The second number is quarter hundred weights so a quarter hundred weight is 28 pounds. In this example 2 times 28 is 56. The last number is actually pounds so in this example 3 pounds. Now add them all up and you get the weight of 112 + 56 +3 = 171, the weight of the anvil. If there are numbers close together not separated by a space it is probably an American forged anvil and the number is the actual weight. If there are no numbers on the side it is also probably an American forged anvil.
I would modify the stand to make it a 3 legged stand with the third leg under the horn and angle them all out about 17 degrees. A 3 legged stand is always stable, like a milking stool. I would value this anvil between $3.00 and $5.00 per pound. If it has no weight markings you can probably put it on a bathroom scale. Let me know if I can help you. Wayne www.WayneCoeArtistBlacksmith.com waynecoe@highland.net |
#3
|
||||
|
||||
Quote:
Thanks Wayne, Here is the only info I've found online that made me think it is a fisher. If you look about middle of the page there is an anvil that looks very much like this one. http://www.anvilfire.com/21centbs/an...her-norris.php __________________ Mark |
#4
|
||||
|
||||
Here is the reply from the Fisher Norris Factory Museum FB page.
That is how the marking were done for a while in the late 1930's. I have a few marked with the very faint FISHER under the horn. It looks like a 20 on the leg, indicating about a 200 lb anvil. Aside from a couple of torch cuts, the anvil is in great shap __________________ Mark |
#5
|
|||
|
|||
Quote:
|
#6
|
||||
|
||||
No disrespect Wyne, but most of my readings/research have indicated that Fishers were cast iron based not wrought iron. However, that did not detract from their quality as an anvil. They were/are very popular old school anvils. That one looks to be in very good shape and should serve you well. Most of the later models had the full weight cast in place across the foot or base of the anvil where the "19*" # is. This must be an older model. If it's got decent rebound you're good to go. Great alround size for most work.
There is a large very detailed book on older anvils (can't recall the title). It had very extensive sections on Fishers and Haye Buddens - history and fabrication. Great read. __________________ Carl Rechsteiner, Bladesmith Georgia Custom Knifemakers Guild, Charter Member Knifemakers Guild, voting member Registered Master Artist - GA Council for the Arts C Rex Custom Knives Blade Show Table 6-H Last edited by Crex; 09-06-2018 at 06:50 AM. |
Tags |
a, angle, anvil, base, blacksmith, degrees, fac, forged, forging, gallery, horn, identification, iron, made, make, marking, scale, steel |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Anvil needs identification | ckluftinger | The Newbies Arena | 9 | 04-04-2011 09:34 AM |
Identification | safetyflyer | Knife Making Discussions | 0 | 05-09-2005 02:56 AM |
anvil identification help needed | BrianT | Tool Time | 7 | 11-12-2002 03:11 PM |
Anvil identification ?? | nifeman | The Outpost | 7 | 02-22-2002 10:29 AM |