MEMBER ITEMS FOR SALE
Custom Knives | Other Knives | General Items
-------------------------------------------
New Posts | New PhotosAll Photos



Go Back   The Knife Network Forums : Knife Making Discussions > Custom Knife Discussion Boards > Knife Making Discussions > The Newbies Arena

The Newbies Arena Are you new to knife making? Here is all the help you will need.

Reply
 
Thread Tools Display Modes
  #1  
Old 02-12-2003, 06:56 PM
David Peterson David Peterson is offline
Skilled
 
Join Date: Jun 2002
Posts: 288
Bolsters on stub tang?

Hey all,
I have a knife blade that I've been working on, and I now want to convert it to a stub tang design. I've already made the bolsters to go on the full tang version, but thought about using them on the stub tang too. I'm looking for opinions on if it's possible, any snags I might run into etc.. Here's a quick and dirty picture of what I'm thinking. The handle outline is the blade as it is now, and the stub is what I want it to be. I thought about pinning the bolsters on first, then grinding away most of the handle, and finishing up to the bolsters with a file. Then I would drill the wood and fit it up to the bolsters, with a spacer, and then glue it all together. I've never seen a knife done this way, so I thought I'd get everyones opinions first. Any thoughts?



-Dave
Reply With Quote
  #2  
Old 02-12-2003, 08:11 PM
Jamey Saunders's Avatar
Jamey Saunders Jamey Saunders is offline
Moderator
 
Join Date: Jul 2002
Location: Portal, GA - If you know where it is, you probably got a speeding ticket.
Posts: 1,951
Send a message via AIM to Jamey Saunders Send a message via MSN to Jamey Saunders Send a message via Yahoo to Jamey Saunders
I can't recall ever seeing a knife made this way either, but that's not saying it can't be done. I'd fix the bolsters then file the back of the bolsters carefully to make the handle fit.

Everything was once done first by somebody.


__________________
Jamey Saunders -- Charter Member, GCKG
(Got a question? Have you tried to for the answer?)

"I won't be wronged, I won't be insulted, and I won't be laid a hand on. I don't do these things to other people, and I require the same of them." --John Wayne, in The Shootist
Reply With Quote
  #3  
Old 02-12-2003, 08:42 PM
floridafred's Avatar
floridafred floridafred is offline
Skilled
 
Join Date: Dec 2002
Location: Boynton Beach, Florida
Posts: 344
Thumbs up Yes, it can be done

I have made several of these and plan to continue. Putting them together is pretty straight forward. I finish the bolster and the wood handle at the same time.



__________________
Regards, Fred

"Great spirits have always encountered violent opposition from mediocre minds". Albert Einstein
Reply With Quote
  #4  
Old 02-12-2003, 08:45 PM
floridafred's Avatar
floridafred floridafred is offline
Skilled
 
Join Date: Dec 2002
Location: Boynton Beach, Florida
Posts: 344
I forgot to mention that I defferentially heat treat so that I can file the shoulders square with the back of the bolsters. That is the most important thing for a good fitup.


__________________
Regards, Fred

"Great spirits have always encountered violent opposition from mediocre minds". Albert Einstein
Reply With Quote
  #5  
Old 02-13-2003, 02:07 PM
David Peterson David Peterson is offline
Skilled
 
Join Date: Jun 2002
Posts: 288
Fred,
That's one good looking knife. Simplicity at its best. Do you have to pin these types of knives, or is that a design feature? If you have to pin them, how do you go about getting the holes lines up correctly? Thanks.

-Dave
Reply With Quote
  #6  
Old 02-13-2003, 03:33 PM
floridafred's Avatar
floridafred floridafred is offline
Skilled
 
Join Date: Dec 2002
Location: Boynton Beach, Florida
Posts: 344
Thanks Dave: Yes the bolsters have two pins and the wood handle two pins which are visible. The way I do it is to first polish the front of the bolsters. Then I glue one bolster to the knife just where I want it. I use instant glue. I then drill through the knife holes to get the holes right in the bolster. I take a heat gun and heat up the bolster until the glue lets go. Be careful not to heat the blade too much. I wrap a wet cloth around it if it begins to heat.

When I have the bolster free I glue the two bolsters together the same way and drill through one bolster to line up the holes in the other. Again the heat gun separates them. Be sure to clean of any remaining glue each time,

Now the holes in the knife and the bolsters are in perfect alignment to accept the pins. This is the short version so if you have any questions let me know.


__________________
Regards, Fred

"Great spirits have always encountered violent opposition from mediocre minds". Albert Einstein
Reply With Quote
  #7  
Old 02-13-2003, 06:41 PM
David Peterson David Peterson is offline
Skilled
 
Join Date: Jun 2002
Posts: 288
Fred,
Hey that's a great trick to get the bolsters on. I'm definitely going to use that one.

How did you get the pins in the handle to line up with holes in the stub tang? Did you drill the hole in the metal first, before heat treat, or did you anneal the stub and drill through both the wood and metal all at once? Thanks.

-Dave
Reply With Quote
  #8  
Old 02-13-2003, 06:52 PM
floridafred's Avatar
floridafred floridafred is offline
Skilled
 
Join Date: Dec 2002
Location: Boynton Beach, Florida
Posts: 344
I fill a coffee can with water. Place a rod thru one hole drilled for the tang and suspend the blade in water with the tang held above the water by the rod which rests on the top of the can. I then draw the tang back with a propane or Mapp torch. I then drill the handle and tang at the same time for a perfect fit.


__________________
Regards, Fred

"Great spirits have always encountered violent opposition from mediocre minds". Albert Einstein
Reply With Quote
  #9  
Old 02-14-2003, 04:15 AM
Ansoknives's Avatar
Ansoknives Ansoknives is offline
Founding Member / Moderator
 
Join Date: Jun 2002
Location: Farre, Denmark
Posts: 408
Send a message via ICQ to Ansoknives Send a message via AIM to Ansoknives
I have done it a few times and it works great with no big difficulties...its just different so if you are used to work differently just take it slow...this ?ne was made like that......I fitted the bolsters as close to the tang as possible and then very carefully with a small wheel on my grinder fitting the 3 parts together..I did this with the bolsters only attached with try pins.....took the thing apart and straigtened the back of the bolster on my diskgrinder to get the perfect fit. I don?t much care for soldered guards so this is the way I do it....





__________________
Jens Ans?
Visit me at www.ansoknives.com

Reply With Quote
  #10  
Old 02-14-2003, 08:54 AM
Jamey Saunders's Avatar
Jamey Saunders Jamey Saunders is offline
Moderator
 
Join Date: Jul 2002
Location: Portal, GA - If you know where it is, you probably got a speeding ticket.
Posts: 1,951
Send a message via AIM to Jamey Saunders Send a message via MSN to Jamey Saunders Send a message via Yahoo to Jamey Saunders
Wow, Jens! I love that knife. I think that's my favorite out of all the pictures you have ever posted here. Very nice.


__________________
Jamey Saunders -- Charter Member, GCKG
(Got a question? Have you tried to for the answer?)

"I won't be wronged, I won't be insulted, and I won't be laid a hand on. I don't do these things to other people, and I require the same of them." --John Wayne, in The Shootist
Reply With Quote
Reply

Tags
blade, knife, knives


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -5. The time now is 10:28 PM.




KNIFENETWORK.COM
Copyright © 2000
? CKK Industries, Inc. ? All Rights Reserved
Powered by ...

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
The Knife Network : All Rights Reserved