|
|
Fit & Finish Fit and Finish = the difference in "good art" and "fine art." Join in, as we discuss the fine art of finish and embellishment. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
How to get tang handle to be polished
Im working on a tang knife. Micarta hangle worked my way up from 220,400,600,800,1000 how do i get the metal handle material mirror andnot burn the micarta. I tried a green roush did work to well, im stuck. I need some help. The blade is mirror polished too
|
#2
|
|||
|
|||
Admittedly, I'm not a big believer in mirror finishes on knives. They don't last. Not all handle material will take a high gloss finish and end up looking like polished stone. Probably most won't. You could try sanding the micarta scales out to 2000 grit and buff with a fine rouge but I doubt that you will ever get that deep of a shine on it. Even if you did you might end up with a handle that will be slick in wet hands. Unless I was making something that was strictly an art knife, one that would spend it's existence in a display case, I would pay much more attention to function that a bright finish.
Doug __________________ If you're not making mistakes then you're not trying hard enough |
#3
|
||||
|
||||
Some metals don't polish well - notably D2.
__________________ God bless Texas! Now let's secede!! |
#4
|
|||
|
|||
Slip23us...First thing is "Why the mirror finish"?? I have to agree with Doug on this. Most of the knifemakers on this forum would advise against a mirror finish. A mirror finish is a lot of work to achieve, and it will almost certainly be damaged the first time the knife is put to use. However, if the knife is only intended to be a showpiece...then it's only a matter of how much work do you want to put into it.
As far as polishing the tang goes....the first thing is that it should have been done prior to putting on the handle....but since you are where you're at...you basically have two options. The first option is to continue working as you have to achieve the mirror finish...or work the finish out by hand to avoid damaging the handle. This is going to be a highly work-intensive effort...but it will get you there. The second option..and in my view the better option...is to "degrade" the mirror finish on the rest of the blade to match the finish on the tang. Using the second option is much easier to do, and will yield a much more serviceable knife...assuming the knife is intended to be actually used as a knife. Part of being a knifemaker is to know and understand how the knife is to be used, and to assure that all aspects of the knife are suitable for it's intended use and function. |
#5
|
|||
|
|||
I know no more mirror finshes, its alot of work, Im going to keep doing satin finishes. So ill have to get some more sandpaper from 1000 to 2000 and pink rouge and a cloth to wipe away rouge. One more question which website is the best for a beginner like me for getting tips.. So far I like this site but theres others like bladefourms and knifeforms... plus thank you to Trugrit in onatrio Ca for all your help ,,,, thanks for the tips guys
|
#6
|
|||
|
|||
I don't think that there is such a thing as too much information. You will have personality clashes on all of them. I know one where a very accomplished and skilled master metal worker was banned due to his attitude with other people on the site. Not all moderators are respected as much as others. There are conflicts with strongly held opinions on all the sites. You just have to learn to take what you can use and ignore the rest.
Doug __________________ If you're not making mistakes then you're not trying hard enough |
#7
|
||||
|
||||
Personally, this is my favorite forum, with Knifedogs being a close second. I'm also a moderator on knifeforums. A large number of serious knifemakers have stopped going to/participating on Bladeforums due to the personal attacks that occur there, and just the general "big head" attitude that a lot of folks there seem to have. The straw that broke the camel's back for me was what I considered a vicious attack on Ed Fowler... whether you agree or disagree with what he does and how he does it is irrelevant, he's given a lot, for a long time to the knife world.....and the total disrespect/degradation shown to him on that forum was simply wrong and uncalled for.
__________________ WWW.CAFFREYKNIVES.NET Caffreyknives@gmail.com "Every CHOICE has a CONSEQUENCE, and all your CONSEQUENCES are a result of your CHOICES." |
#8
|
||||
|
||||
Other forums
I`ve been a member here since Alex started the original forum.Ed I whole heartedly agree with you about bladeforum and the crap about Ed Fowler. Robert
|
Tags |
art knife, blade, handle, knife, knives, material, polish, scales, stone, tang, tips |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
stick tang handle | Kallinen Knives | The Newbies Arena | 2 | 04-29-2008 07:51 AM |
Burning a tang through handle | dave Stifle | Fit & Finish | 12 | 05-02-2007 09:33 PM |
Finishing the handle-guard, handle-tang junction? | C_Claycomb | Fit & Finish | 7 | 06-25-2003 01:33 AM |
Hidden tang handle | JimmySeymour | The Newbies Arena | 1 | 04-27-2003 08:02 AM |
Best handle for partial tang? | dmelton | The Newbies Arena | 4 | 05-09-2002 08:46 AM |