|
|
The Newbies Arena Are you new to knife making? Here is all the help you will need. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1084 & Cocobolo
Messed around with that round thing on the end of the tool arm and some clay and here's how it turned out.
1084 HT w/ Clay backing Cocobolo SS Corby & Thong tube Comments and criticisms welcomed. |
#2
|
||||
|
||||
Very Beautiful Knife!! Love that hamon!! Wish I could use Cocobolo, but I am allergic to the stuff..
Frank __________________ ?Happiness... it lies in the joy of achievement, in the thrill of creative effort.? Franklin D. Roosevelt |
#3
|
||||
|
||||
KEWL dude! I like sculptured handes too! ....and a hamon to boot....nice!
__________________ Dennis "..good judgement comes from experience, experience comes from poor judgement.." -Gary McMahan, a cowboy poet and good dancer. http://www.facebook.com/home.php#!/p...24112090995576 |
#4
|
||||
|
||||
That's sweeeeeeeet!
The Cocobolo makes for a beautiful handle! The hamon really pops, couple that with a great knife and the cocobolo make for on great combo! What was your medium for obtaining the hamon and process you used, if you don't mind sharing? I don't see many that come across as well as yours! __________________ C Craft Customs With every custom knife I build I try to accomplish three things. I want that knife to look so good you just have to pick it up, feel so good in your hand you can't wait to try it, and once you use it, you never want to put it down ! If I capture those three factors in each knife I build, I am assured the knife will become a piece that is used and treasured by its owner! C Craft Last edited by C Craft; 05-06-2010 at 09:45 AM. |
#5
|
||||
|
||||
Nice work. That's a good combination of materials.
__________________ John Doyle You have nothing to fear but fear itself...........and bears. |
#6
|
|||
|
|||
Thanks for the compliments Guys
For the Hamon. I grind to about 220 (what ever the 3M Gator A100?s correspond to). Do the knifemakers normalization 3X. Coat the spine with a thinned out furnace cement, (http://www.ecrater.com/product.php?pid=2021995) then ?drizzle? strings of the cement from the spine towards the edge. Something like this - Heat treat and quench in Mineral oil. Clean up A100-A65-A45-A30- grey scotchbrite belt. Hit with the buffer and Green compound (went back to the belts a couple of time due to thinking I had the scratches out but didn?t) and etched in Ferric. |
#7
|
||||
|
||||
Quote:
Do you wait for the clay to harden before you heat and quench?? Thanks so much for sharing !! Frank __________________ ?Happiness... it lies in the joy of achievement, in the thrill of creative effort.? Franklin D. Roosevelt |
#8
|
|||
|
|||
Frank
I usually put it on and do a quick bakeout to drive the moisture out - something like 5 seconds in then out watching the steam come off the cement and then repeat until there is no more steam coming off the blade You can go right in but I did have failures due to the material spalling off cause of the moisture. Waiting overnight didn't seem to improve the results. If you are using satinite - I had better luck waiting overnight before heat treating. Hope that helps |
Tags |
blade, knife |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cocobolo? | Pelallito | Fit & Finish | 10 | 07-26-2009 07:19 AM |
Passmore w/ Cocobolo | Jeff Higgins | The Display Case | 4 | 01-21-2006 08:26 AM |
Nice cocobolo F/S | SPryor | The Supply Center | 3 | 12-04-2005 09:22 PM |
Cocobolo | DracAmy | The Newbies Arena | 4 | 05-31-2002 07:00 PM |