|
|
The Newbies Arena Are you new to knife making? Here is all the help you will need. |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
1085 at rc50
Okay, here I go. I've read a lot of the posts (before joining), I've researched on the web, and now I want to build a knife. However, I want to start with just the handle.
So I've looked for premade blades, and I found a supplier who offers an 8 inch predrilled, ground blade in 1085 with a hardness of rc50. But from what I've read here and elsewhere, 50 seems a bit low. I will say that it's just for an everyday camp knife, not meant for chopping trees. Can I really do okay with that soft of a blade? |
#2
|
||||
|
||||
I guess you could but why would you when there are so many alternatives available? If all you want to do is the handle - and that's a perfectly good way to start - then just buy any one of the hundreds of commercially available kit blades offered at virtually every knife supply house. Most of those blades are stainless but not all of them (nothing wrong with stainless anyway). In many instances, they will also have partially finished sheaths for their blades so you can learn a bit about finishing sheaths while you're at it.
Any of the big suppliers like Jantz or Texas Knifemakers have these blades. You might try knifekits.com , they don't have the largest variety of blades but they do have a nice website.... |
#3
|
|||
|
|||
If the HRc of 50 is accurate, you could get something harder by hammering the edge of the blade. Pass on that one. As Ray said, there are plenty of good finished blades out there in stainless, carbon, and even pattern welded steel. Any reputable seller of finished blades and knife kits will list the approximate hardness so get one that has a hardness of around HRc 58-60.
Doug __________________ If you're not making mistakes then you're not trying hard enough |
#4
|
|||
|
|||
Quote:
|
#5
|
|||
|
|||
Five2go...I find it strange that a blade made of 1085 would only be hardened to RC50 since it is easily hardened to RC60+. This sounds to me like either it was a misprint or possibly tempered back to that hardness. In either event, I'd pass on that blade and buy one of the available kit blades from a reputable dealer. You are correct in being concerned about a hardness of RC50. I doubt that you would be satisfied with such a knife. As Doug suggested, an RC of 58-60 seems to be a popular number for general usage.
|
#6
|
|||
|
|||
Quote:
After looking at some other vendors, I ordered a 440a blade that is rated at 55-56. By the way, the rc 50 blades were offered by Atlanta Cutlery. |
#7
|
|||
|
|||
Perhaps...
Perhaps the reason Chicago Cutlery is offering out blade blanks with such a low RC is that they are anticipating the buyer will want to add his own handles with non standard fasteners or possibly do file work on the piece before re-heat treating to a more acceptable RC.
The lower RC would allow the assembler to customize the size and/or pattern of fastener holes are drilled. Quien Sabe? Last edited by rscoffey; 10-23-2012 at 01:10 PM. Reason: correction |
#8
|
||||
|
||||
An other place to look for blades, if u want to practice handles, is your own kitchen. I found an old knife I owned out in the yard. I had a dog that could steal anything off the counter how she could get big knives out the dog door and never get cut I don't know. Anyway this knife is carbon steel it has rust on one side and is shinny along the edge. I ground over 1/4" off the blade sharpening on the can opener sharpener. The handle is chewed up pretty bad. I was going to pitch it but this is a good place to practice and not worry about ruining expensive material. You don't need an old knife you can sort of give a face lift to the cutlery your using. New handles, clean um up, sharpen them. (not on the can opener) Good as new!!!
|
Tags |
art, back, blade, build, camp knife, cutlery, edge, file, file work, handle, kit, kits, knife, knife supply, knifekits.com, knives, made, pattern, sharpening, sheaths, steel, supply |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Making Mokume from 1010, 1085 and copper | ArielSalaverria | The Damascus Forum | 12 | 04-04-2006 08:35 PM |
1085/416/52100 San Mai All Integral Kitchen Knife | ArielSalaverria | The Display Case | 1 | 09-13-2005 06:57 PM |
1085 Vs. 1095 Sound Out! | Fox Creek | Heat Treating and Metallurgy | 10 | 07-17-2005 09:09 PM |